Add flash_get_unique_id to hardware_flash

This commit is contained in:
Luke Wren 2021-01-24 16:42:14 +00:00 committed by Graham Sanderson
parent dd2b7039a5
commit 620c75b9b8
2 changed files with 97 additions and 0 deletions

View File

@ -7,8 +7,17 @@
#include "hardware/flash.h"
#include "pico/bootrom.h"
#include "hardware/structs/ssi.h"
#include "hardware/structs/ioqspi.h"
#define FLASH_BLOCK_ERASE_CMD 0xd8
// Standard RUID instruction: 4Bh command prefix, 32 dummy bits, 64 data bits.
#define FLASH_RUID_CMD 0x4b
#define FLASH_RUID_DUMMY_BYTES 4
#define FLASH_RUID_DATA_BYTES 8
#define FLASH_RUID_TOTAL_BYTES (1 + FLASH_RUID_DUMMY_BYTES + FLASH_RUID_DATA_BYTES)
#define __compiler_barrier() asm volatile("" ::: "memory")
//-----------------------------------------------------------------------------
@ -99,3 +108,72 @@ void __no_inline_not_in_flash_func(flash_range_program)(uint32_t flash_offs, con
flash_flush_cache(); // Note this is needed to remove CSn IO force as well as cache flushing
flash_enable_xip_via_boot2();
}
//-----------------------------------------------------------------------------
// Lower-level flash access functions
// Bitbanging the chip select using IO overrides, in case RAM-resident IRQs
// are still running, and the FIFO bottoms out. (the bootrom does the same)
static void flash_cs_force(bool high) {
uint32_t field_val = high ?
IO_QSPI_GPIO_QSPI_SS_CTRL_OUTOVER_VALUE_HIGH :
IO_QSPI_GPIO_QSPI_SS_CTRL_OUTOVER_VALUE_LOW;
hw_write_masked(&ioqspi_hw->io[1].ctrl,
field_val << IO_QSPI_GPIO_QSPI_SS_CTRL_OUTOVER_LSB,
IO_QSPI_GPIO_QSPI_SS_CTRL_OUTOVER_BITS
);
}
// May want to expose this at some point but this is unlikely to be the right
// interface to do so. Keep it static
static void __no_inline_not_in_flash_func(flash_do_cmd)(const uint8_t *txbuf, uint8_t *rxbuf, size_t count) {
void (*connect_internal_flash)(void) = (void(*)(void))rom_func_lookup(rom_table_code('I', 'F'));
void (*flash_exit_xip)(void) = (void(*)(void))rom_func_lookup(rom_table_code('E', 'X'));
void (*flash_flush_cache)(void) = (void(*)(void))rom_func_lookup(rom_table_code('F', 'C'));
assert(connect_internal_flash && flash_exit_xip && flash_flush_cache);
flash_init_boot2_copyout();
__compiler_barrier();
connect_internal_flash();
flash_exit_xip();
flash_cs_force(0);
size_t tx_remaining = count;
size_t rx_remaining = count;
// We may be interrupted -- don't want FIFO to overflow if we're distracted.
const size_t max_in_flight = 16 - 2;
while (tx_remaining || rx_remaining) {
uint32_t flags = ssi_hw->sr;
bool can_put = !!(flags & SSI_SR_TFNF_BITS);
bool can_get = !!(flags & SSI_SR_RFNE_BITS);
if (can_put && tx_remaining && rx_remaining - tx_remaining < max_in_flight) {
ssi_hw->dr0 = *txbuf++;
--tx_remaining;
}
if (can_get && rx_remaining) {
*rxbuf++ = ssi_hw->dr0;
--rx_remaining;
}
}
flash_cs_force(1);
flash_flush_cache();
flash_enable_xip_via_boot2();
}
// Use standard RUID command to get a unique identifier for the flash (and
// hence the board)
static_assert(FLASH_UNIQUE_ID_SIZE_BYTES == FLASH_RUID_DATA_BYTES);
void flash_get_unique_id(uint8_t *id_out) {
#if PICO_NO_FLASH
panic_unsupported();
#else
uint8_t txbuf[FLASH_RUID_TOTAL_BYTES] = {0};
uint8_t rxbuf[FLASH_RUID_TOTAL_BYTES] = {0};
txbuf[0] = 0x4b;
flash_do_cmd(txbuf, rxbuf, FLASH_RUID_TOTAL_BYTES);
for (int i = 0; i < FLASH_RUID_DATA_BYTES; i++)
id_out[i] = rxbuf[i + 1 + FLASH_RUID_DUMMY_BYTES];
#endif
}

View File

@ -18,6 +18,8 @@
#define FLASH_SECTOR_SIZE (1u << 12)
#define FLASH_BLOCK_SIZE (1u << 16)
#define FLASH_UNIQUE_ID_SIZE_BYTES 8
/** \file flash.h
* \defgroup hardware_flash hardware_flash
*
@ -28,6 +30,10 @@
* synchronisation to make sure no XIP accesses take place during flash
* programming.
*
* Likewise they are *unsafe* if you have interrupt handlers or an interrupt
* vector table in flash, so you must disable interrupts before calling in
* this case.
*
* If PICO_NO_FLASH=1 is not defined (i.e. if the program is built to run from
* flash) then these functions will make a static copy of the second stage
* bootloader in SRAM, and use this to reenter execute-in-place mode after
@ -54,6 +60,19 @@ void flash_range_erase(uint32_t flash_offs, size_t count);
* \param data Pointer to the data to program into flash
* \param count Number of bytes to program. Must be a multiple of 256 bytes (one page).
*/
void flash_range_program(uint32_t flash_offs, const uint8_t *data, size_t count);
/*! \brief Get flash unique 64 bit identifier
* \ingroup hardware_flash
*
* Use a standard 4Bh RUID instruction to retrieve the 64 bit unique
* identifier from a flash device attached to the QSPI interface. Since there
* is a 1:1 association between the MCU and this flash, this also serves as a
* unique identifier for the board.
*
* \param id_out Pointer to an 8-byte buffer to which the ID will be written
*/
void flash_get_unique_id(uint8_t *id_out);
#endif